Parameter Adjustment in the Logistics (Semantic Segmentation) Scenario
In the logistics (semantic segmentation) scenario, the Logistics_Seg_RGBSuction picking configuration folder should be used. This model can be used to obtain all pixels of the object in the image, and therefore obtain the contour and status (overlapped or not) of the object.
Parameter Adjustment Order
-
Set a Working Distance first to limit the range for the camera to capture the data.
-
Adjust the Contour Detection (Smart Placement, Special Shape) parameter to determine whether to process objects whose contours are detected with priority.
-
The objects in the logistics scenario are usually stacked randomly, adjusting the Overlap Detection parameter group can divide the objects into objects that are overlapped and not overlapped.
-
Adjust the Pose Processing parameter group to control the upward offset along the Z-axis to avoid damaging the object.
-
Adjust the Dynamic Place parameter group to adjust the speed of the robot.
-
Adjust the Priority Picking Setting and Pose Sorting Logic parameter group to determine the picking sequence.
Parameter Description
Working Distance
- Minimum Working Distance
-
Description: This parameter is used to specify the minimum distance (in millimeters) between the camera and the object in the scene. If a bin is used, this parameter should be the distance from the camera to the top edge of the bin. Please set the value according to the actual situation.
Default value: 0 mm
Value range: 0–3000 mm
- Maximum Working Distance
-
Description: This parameter is used to specify the maximum distance (in millimeters) between the camera and the object in the scene. If a bin is used, this parameter should be the distance from the camera to the bottom edge of the bin. Please set the value according to the actual situation.
Default value: 3000 mm
Value range: 0–3000 mm
Contour Detection (Smart Placement, Special Shape)
- Prioritize Contours
-
Description: This parameter is used to detect the contours of objects. The more complete the contour of an object is, the higher its priority for picking; the less complete the contour, the lower its priority for picking.
Default setting: selected.
Tuning recommendation: If the project does not have a high requirement for the overlap detection, you can enable this feature to increase the picking success rate and avoid changing bins frequently. If there is a high requirement on the overlap detection and only the objects that are NOT overlapped should be picked, it is recommended to disable this feature.
Overlap Detection
- Max Number of Objects
-
Description: This parameter is used to specify the maximum number of objects that will be considered overlapped.
Default value: 6
Value range: 0–10
Tuning recommendation: Please set the parameter according to the actual situation.
Pose Processing
- Max Number of Output Poses
-
Description: This parameter is used to specify the maximum number of output poses.
Value range: 0–20
- Upward Offset along Z-Axis
-
Description: This parameter is used to specify the offset distance (in millimeters) along Z-axis above the object to prevent the robot from squeezing the object .
Default value: 0
Value range: 0–10 mm
Tuning recommendation: Please set the parameter according to the actual situation.
Dynamic Place
This parameter group can be used to determine the height of the robot end tool when the robot places the object according to the height of the object, and therefore the following two situations can be avoided.
-
If the robot drops the object at a very high height, the object may roll on the fast-running conveyor belt.
-
If the robot places the object at a very low height, the object may collide with the conveyor belt, and both the object and the conveyor belt may be damaged.
When the robot picks the object, it needs to determine the weight of the object. The algorithm in this parameter estimates the object’s weight according to its volume. If the robot picks a heavy object, and the robot is moving at a fast speed, the following consequences may occur:
-
The object cannot be picked successfully.
-
The picked object is thrown out.
-
The package of the object is torn, but the object is not picked up successfully.
- 2D Area Threshold
-
Description: This parameter is used to detect the area of the detected object. If the area of the detected object is larger than this value, the robot speed will be reduced when placing the object. When the area of the detected object is smaller than this value, the robot will place the object with the Robot Placing Velocity.
Value range: 0–10000000 px
- Robot Placing Velocity
-
Description: This parameter is used to specify the speed when the robot places the object. When the area of the detected object is smaller than the set 2D Area Threshold, the robot will place the object with the speed set in this parameter; when the area of the detected object exceeds the set 2D Area Threshold, the robot reduces the placement speed.
Default value: 100%
Value range: 0–100%
Priority Picking Setting
- Priority Picking Direction
-
Description: This parameter is used to set the direction in which the object will be prioritized for picking.
Options:
-
Up
-
Down
-
Left
-
Right
Default setting: Right
-
Pose Sorting Logic
The detected poses in this Step will be sorted according to the pose score in descending order. Pose Score = Object Height × Pose Height Weight + Object Horizontal Position × Object Horizontal Position Weight + Rectangularity × Rectangularity Weight
- Pose Height Weight
-
Description: This parameter is used to set the weight of the pose height when the score of a pose is calculated. If this weight is set to a larger value, objects that are at a high height will be more likely to be picked first.
Default value: 5
Value range: 0–5
- Object Horizontal Position Weight
-
Description: This parameter is used to set the weight of the horizontal position when the score of a pose is calculated. If this weight is set to a larger value, objects that are close to the end in the Priority Picking Direction will be more likely to be picked first.
Default value: 1
Value range: 0–5
- Rectangularity Weight
-
Description: This parameter is used to set the weight of the rectangularity when the score of a pose is calculated. If this weight is set to a larger value, objects with high rectangularity values will be more likely to be picked first.
Default value: 0
Value range: 0–5
Visualization
|
The Visualization parameter group is only used for selecting what will be displayed in the Debug Output window and will not affect the adjustment of the above parameters. |
- Enable
-
Description: Once this option is selected, you can select the items you want to visualize in the Debug Output window.
Default value: selected.
- Visualization Type
-
Description: This parameter is used to specify the items you want to visualize.
Options:
-
Final Score
-
Show Pose Height
-
Show Suction Cup Diameter
-
Show Object Length
Default value: Final Score
-
|
This parameter will only be displayed after the visualization is enabled. |
