FAQs

You are currently viewing the documentation for the latest version (2.1.0). To access a different version, click the "Switch version" button located in the upper-right corner of the page.

■ If you are not sure which version of the product you are currently using, please feel free to contact Mech-Mind Technical Support.

This chapter lists frequently asked questions about robot communication and provides solutions.

Master-Control Communication FAQ

Type	References
Communication establishment	How to Troubleshoot Failed Master-Control Communications?
Communication adaptation	How to Make Sure that the Robot Controller Supports Master-Control Communication?
Others	ABB	Why are DO or DI Signals Occasionally Enabled or Disabled in Advance for ABB Robots in Master-Control Communication?
DENSO	How To Configure DO or DI Signals for DENSO Robots in Master-Control Communication?
Kawasaki	What to Do If An Asterisk (*) Cannot Be Find Before Two PC Program Names During Kawasaki Master-Control Communication? How to Disable StartUp Setting for New Kawasaki Robots?
KUKA	How to Stop Other Communication Programs for KUKA Robots? How to Add or Remove Ports for KUKA Robots?

Type

References

Communication establishment

How to Troubleshoot Failed Master-Control Communications?

Communication adaptation

How to Make Sure that the Robot Controller Supports Master-Control Communication?

Others

ABB

Why are DO or DI Signals Occasionally Enabled or Disabled in Advance for ABB Robots in Master-Control Communication?

DENSO

How To Configure DO or DI Signals for DENSO Robots in Master-Control Communication?

Kawasaki

What to Do If An Asterisk (*) Cannot Be Find Before Two PC Program Names During Kawasaki Master-Control Communication?

How to Disable StartUp Setting for New Kawasaki Robots?

KUKA

How to Stop Other Communication Programs for KUKA Robots?

How to Add or Remove Ports for KUKA Robots?

Standard Interface Communication FAQ

Type	References
Communication establishment	How to Troubleshoot Failed Standard Interface Communications? How to Configure IP Address and Port Number in Robot Communication Configuration? Why Set Host IP Address to 0.0.0.0 When Vision System Acts as Server?
Communication adaptation	How to Make Sure That the Robot Controller Supports Standard Interface Communication?
Standard Interface programs as background programs	How Can the Standard Interface Programs for ABB Robots be Run in the Background? How Can the Standard Interface Programs for KUKA Robots be Run in the Background? How Can the Standard Interface Programs for FANUC Robots be Run in the Background? How Can the Standard Interface Programs for Kawasaki Robots be Run in the Background?
Troubleshooting	[WinError 10013] An Attempt was Made to Access a Socket in a Way That is not Allowed by the Access Control [WinError 10038] An Operation was Attempted on Something That is not a Socket
Network assistance tools	How to Use NetAssist?
PLCs	Why does Pose Data Occasionally Show as 0 Despite Normal Status Code in Siemens PLC Communication? Why does the “Immediate value out of range” Error Occur After Routine Files were Loaded to an AB PLC by Using EtherNet/IP Communication?

Type

References

Communication establishment

How to Troubleshoot Failed Standard Interface Communications?

How to Configure IP Address and Port Number in Robot Communication Configuration?

Why Set Host IP Address to 0.0.0.0 When Vision System Acts as Server?

Communication adaptation

How to Make Sure That the Robot Controller Supports Standard Interface Communication?

Standard Interface programs as background programs

How Can the Standard Interface Programs for ABB Robots be Run in the Background?

How Can the Standard Interface Programs for KUKA Robots be Run in the Background?

How Can the Standard Interface Programs for FANUC Robots be Run in the Background?

How Can the Standard Interface Programs for Kawasaki Robots be Run in the Background?

Troubleshooting

[WinError 10013] An Attempt was Made to Access a Socket in a Way That is not Allowed by the Access Control

[WinError 10038] An Operation was Attempted on Something That is not a Socket

Network assistance tools

How to Use NetAssist?

PLCs

Why does Pose Data Occasionally Show as 0 Despite Normal Status Code in Siemens PLC Communication?

Why does the “Immediate value out of range” Error Occur After Routine Files were Loaded to an AB PLC by Using EtherNet/IP Communication?

General FAQ

Type	References
Networks	Troubleshooting Failed Communications Caused by Firewalls How to Test Whether Communication Can be Established by Using Two IP Addresses? How to Set the IP Address of an IPC?

Type

References

Networks

Troubleshooting Failed Communications Caused by Firewalls

How to Test Whether Communication Can be Established by Using Two IP Addresses?

How to Set the IP Address of an IPC?

FAQs

Master-Control Communication FAQ

Standard Interface Communication FAQ

General FAQ

We Value Your Privacy