Scene Objects
This section introduces the scene objects and corresponding configurations.
Introduction
Scene objects, usually including the safety fence, picking bin, tray, camera, camera stand and so on, refer to objects in the real scenarios where the robot performs various tasks.
Scene Object Model
Adding scene object models makes the scene in the software closer to the real scenario, which facilitates the collision detection and path planning. You can create models of a cuboid, bin, or cylinder. You can also use a custom model imported from outside the software. The supported format of the visualization model and collision model are shown in the table below.
| Format | STL | OBJ | DAE | Binvox |
|---|---|---|---|---|
Visualization model |
√ |
√ |
√ |
× |
Collision model |
√ |
√ |
× |
× |
The Parent-Child Relationship of the Scene Objects
You can establish a parent-child relationship between scene objects. Once the relationship is established, the child model will be moved as well if the parent model is moved, and the child model will be deleted as well if the parent model is deleted. However, the parent model will not be affected if you move or delete the child model individually.
Configure the Scene Object
You can add, modify, or delete the scene objects in the Resources panel.
Add a Scene Object
Please follow the steps below to add a Cuboid, Cylinder, or Bin type scene object.
-
Go to , and click + to open the Scene Object Configuration window.
-
In the Object Settings tab, select the Scene Model type in the drop-down list.
-
Set the X, Y, Z (length, width, height) for a Cuboid model.
-
Set the Radius and Height for a Cylinder model.
-
Set the X, Y, Z (length, width, height), and Thickness for a Bin model and then Set the Effective Range for the Vision Pose of the Bin.
-
-
Enter a custom name for the scene model in the Object Name text box.
-
If you do not want the currently added scene object to be involved in the collision detection, please unselect the Involve in collision detection parameter.
-
If you do not want the currently added scene object to be selected in the 3D simulation area, please unselect the Model selectable parameter.
-
-
By default, the newly added scene object is located at the origin of the robot base reference frame. You can click the Object Pose tab in the Scene Object Configuration window to switch the configuration interface, and modify the parameters to adjust the pose of the scene object.
-
Click OK.
Please follow the steps below to add a Custom model.
-
Click the + next to , and select the collision model and visualization model in the pop-up window, and then click Open.
-
Go to , and click + to open the Scene Object Configuration window.
-
In the Object Settings tab, select Custom model as the Scene Model.
-
Set the model used for the collision detection as the Collision model.
-
Set the model used for visualization in the 3D simulation area as the Visualization model.
-
Enter a custom name for the scene model in the Object Name text box.
-
If you do not want the currently added scene object to be involved in the collision detection, please unselect the Involve in collision detection parameter.
-
If you do not want the currently added scene object to be selected in the 3D simulation area, please unselect the Model selectable parameter.
-
-
By default, the newly added scene object is located at the origin of the robot base reference frame. You can click the Object Pose tab in the Scene Object Configuration window to switch the configuration interface, and modify the parameters to adjust the pose of the scene object.
-
Click OK.
| If the “Collision model” of a “Custom model” is in STL format, it is recommended to create a cuboid or cylinder to cover the custom model for a higher accuracy of the collision detection. |
If you need to add more tools, please repeat the above steps.
|
Delete the Scene Object
Follow either of the following steps to delete a scene object.
-
Select the scene model in the 3D simulation area or the model name under and press the Delete key.
-
Right-click the scene object in the 3D simulation area or the model name under and select Delete in the context menu.
Modify the Scene Object
-
Follow either of the following steps to open the Scene Object Configuration window.
-
Double-click the object model in the 3D simulation area.
-
Go to and double-click the scene object name.
-
Right-click the name of the scene object under and select Scene Object Configuration in the context menu.
-
-
Modify the parameters according to the actual requirement.
-
Click OK.
| You can also select the scene object in the 3D simulation area, and adjust the model pose with the dragger. |
Set the Effective Range for the Vision Pose of the Bin
When you add a bin as the scene model, you will need to configure the effective range for the vision pose in the Bin Settings tab.
-
If the bin is only used as a scene model and it has no impact on the effective range for the vision pose, please unselect the Set effective range for pose parameter.
-
If the vision pose must be in the bin, please select In the bin.
-
If the vision pose may be above the bin top, please select In the bin and above the bin top and set the Height range above bin parameter.
-
If you want to customize an effective range, please select Custom effective range and set parameters in Effective Range of Pose.