Master-Control Communication Setup

You are currently viewing the documentation for the latest version (2.1.0). To access a different version, click the "Switch version" button located in the upper-right corner of the page.

■ If you are not sure which version of the product you are currently using, please feel free to contact Mech-Mind Technical Support.

This guide shows you how to set up master-control communication with a KUKA robot.

Preparation

Check Controller and Software Compatibility

Controller model: KUKA KR C4
Controller system software version: KSS 8.2, 8.3, 8.5 or 8.6
Click here for instructions
1. Click , and then select Help Info.
2. Check the controller system software version in the Info interface.
Add-on software package: Ethernet KRL (V 2.2.8, 3.0.3 or 3.1.2.29)

The correspondence between KSS and Ethernet KRL versions is as follows:

KSS version Ethernet KRL version

8.2 or 8.3

2.2.8

8.5

3.0.3

8.6

3.1.2.29

Click here for instructions

Click Options in the Info interface to view the Ethernet KRL version.

KSS version	Ethernet KRL version
8.2 or 8.3	2.2.8
8.5	3.0.3
8.6	3.1.2.29

All teach pendant actions in this chapter are performed on KSS 8.6.

Set up the Network Connection

Connect the Hardware

KR C4 Compact: X66 port
Other KR C4 controllers: KLI port

Set the IP Address

Switch to the Expert mode:
1. Click , and then select Configuration User group to enter the log-on interface.
2. Select Expert, enter the password (the default password is kuka), and then click Log on.
Set the IP address:
1. Click , and then select Start-up Network configuration to enter the network configuration interface.
2. Input an IP address in the same subnet as that of the IPC, and then click Save. Click Yes and OK, respectively, in the next two pop-up windows.
Restart the robot controller to finish setting the IP address:
1. Click , and select Shutdown to enter the shutdown interface.
2. Click Reboot control PC in the shutdown interface.

Load the Program Files to the Robot (Auto)

You can perform the following operations to allow the loader to auto-load master-control programs to the robot.

If the auto-load process fails and you cannot resolve the issue, proceed to Load the Program Files to the Robot (Manual).

Navigate to Communication Component/Robot_Server/Robot_FullControl/kuka/kuka_opt from the installation directory where Mech-Vision and Mech-Viz are installed, open the desired folder based on your robot system version, and then copy the Mech-Mind.kop file to your flash drive.
Plug the flash drive into the robot controller and switch to the expert mode.

Click , and then select Configuration User group to enter the log-on interface.

Select Expert, enter the password (the default password is kuka), and then click Log on.
Click , and then select Start-up Additional software.
In the following interface, select New software Configure Path selection.
In the following interface, select the disk that corresponds to the flash drive and click Save. In this example, disk F is selected. The actual disk may be different from the disk that is used in this example. Select the disk based on actual scenarios. Then, return to the preceding interface and click Save.
In the installation interface, the Mech-Mind software package appears. Check the box next to the package to select the package and click Install.
In the following pop-up windows, select OK Yes Yes.
After the software is installed, click , select Start-up Additional software, and then check whether Mech-Mind appears in the installed software list. If the software is installed, click Restart in the lower-right corner of the interface to restart the controller.
After the controller is restarted, click S in the upper part of the teach pendant interface. If a green light is displayed in the State column of EX1 and the mm_server module is selected in the Selected module column, the installation is complete.

After the installation is compete, proceed to Master-Control Communication.

Load the Program Files to the Robot (Manual)

If you have completed operations in Load the Program Files to the Robot (Auto), skip this section.

Switch to the Expert Mode

Click , and then select Configuration User group to enter the log-on interface.
Select Expert, enter the password (the default password is kuka), and then click Log on.

Back up the Robot Program

Make sure you have switched to the expert mode. Otherwise, the flash drive will not show up on the teach pendant.

Plug the flash drive that stores the backup files into the controller, and make sure that the flash drive shows up on the teach pendant.
Click , select File Archive USB (cabinet) All, and then click Yes in the pop-up window to start the backup process.
The following message is displayed when backup is in process. Once the backup is complete, this message disappears and a ZIP file is created in the flash drive. Lastly, remove the flash drive.

Prepare the Files

Navigate to Communication Component/Robot_Server/Robot_FullControl/kuka/kuka_new from the installation directory where Mech-Vision and Mech-Viz are installed. Copy all program files to your flash drive.

Make sure you have switched to the expert mode. Otherwise, the flash drive will not show up on the teach pendant.
Plug the flash drive into the controller, click the flash drive on the left side of the teach pendant, and then locate the folder that contains the program files.
Select the mm_motion file, click Edit, and then click Copy in the pop-up menu bar.
Navigate to C:\\KRC\\ROBOTER\\Config\\User\\Common\\EthernetKRL, click Edit, and then select Paste in the pop-up menu bar. Repeat the above operations to copy the mm_status file to the target folder.
Refer to the above operations to copy the other five files to the mechmind folder in the R1 folder. If the mechmind folder does not exist, create the folder.

Long-press and drag to select multiple adjacent files.

Create the mechmind folder:

Click the R1 folder and click New.

Input mechmind as the folder name in the pop-up window and click OK to create the mechmind folder.

Set Autostart for Background Program

Switch to the expert mode based on the preceding instructions.

Click S on the teach pendant and then click Display/Assign.
Click Cold start configuration to jump to the Cold start configuration interface.
Click the blank in the drop-down menu on the right of SYS.
Then, clear the Autostart checkbox on the right of SYS.
Similarly, select mm_server in the drop-down menu for EX1 and make sure that Autostart is checked.
Click Current display/assignment to jump to the current display/assignment interface. Click the text box to the right of SYS, and then click Deselect.
Click the text box to the right of SYS again, and select the blank in the drop-down menu.
Similarly, select mm_server from the drop-down menu for EX1 and click Select/Start.

Test Master-Control Communication

Select Foreground Program

Open the mechmind folder, select mainmodule.src, and then click Select.

Run Program in the AUT Mode

Switch the mode: Turn the key switch to horizontal, select T1 or AUT in the pop-up dialog box on the screen, and then turn the switch back to vertical.
Switch to the T1 mode as described in the above step. Click O, and then click I in the pop-up window to switch the status of Drives. If the status of Drives is I at the start, ignore this step.
Set an appropriate velocity for the robot before moving the robot, and observe its movements to avoid accidents. Press the enabling switch (either one of three) on the back of the pendant and the green start button on the front at the same time to move the robot back to the Home position. When the screen displays a message saying Programmed path reached (BCO), release the enabling switch and the green start button.
Switch to the AUT mode based on the preceding operations, and press the start button to run the master-control program (the R icon should turn green).

Create a Mech-Viz Project

Open Mech-Viz, press Ctrl+N on the keyboard to create a new project. Select the robot model corresponding to your real robot brand and model on the interface as shown below.
Press Ctrl+S and create or select a folder to save the project.
Right-click the project name in the left panel in Mech-Viz and select Autoload Project.

Connect to the Robot

Click Master-Control Robot on the toolbar of Mech-Viz.
Input the IP address of the real robot in Robot IP address (the IP address in the picture is only an example). Click Connect the robot.

If Mech-Viz successfully connects the real robot, the current status will change to Connected. Meanwhile, the icon in the toolbar will turn from blue to green.

If the connection fails, please double-check the robot IP address.

Move the Robot

In the toolbar of Mech-Viz, change the “Vel.” (velocity) and “Acc.” (acceleration) parameters to 5%.
Click Sync Robot in the toolbar, and you can synchronize the poses of the simulated robot in the 3D simulation space with the poses of the real robot. Then click Sync Robot again to unselect it.
In the Robot tab, slightly adjust the value of “J1”, for example, from 0˚ to 3˚. This operation will move the simulated robot.
Click Move real robot and check if the real robot has moved. If the real robot has reached the JPs set for the simulated robot, the master-control communication is working.

When moving the robot, please ensure the safety of personnel. In the case of an emergency, press the emergency stop button on the teach pendant!

Precautions

If you failed to master-control the robot by using Mech-Viz but can successfully ping the robot IP on the IPC, please restart Mech-Viz software.
If the robot lost communication with Mech-Viz when running, it will automatically try to reconnect. If the robot still cannot connect Mech-Viz, you can try restarting the background program by performing these operations:

Click S, select mm_server from the drop-down menu, click Deselect, and then click Select/Start. If an error message pops up, click Confirm all. After restarting the program, complete operations in the Run Program in the AUT Mode section.