ABB Setup Instructions (RobotWare 7)

You are currently viewing the documentation for version 1.7.4. To access documentation for other versions, click the "Switch Version" button located in the upper-right corner of the page.

■ To use the latest version, visit the Mech-Mind Download Center to download it.

■ If you're unsure about the version of the product you are using, please contact Mech-Mind Technical Support for assistance.

Check Controller and Software Compatibility

  • Controller: OmniCore.

  • Controller system software version: RobotWare 7.3 or higher

  • Control module option: 3114-1 Multitasking

The detailed instructions are as follows.

  1. In the Home interface of the teach pendant, tap Settings  System to check the RobotWare version.

    robotware home
    robotware check1

  2. Tap About and you can confirm the RobotWare version, which should be above 7.3, in System Details.

    robotware check2

  3. Check whether 3114-1 Multitasking is in the System Options.

    robotware check3
    The robot cannot be connected via Master-control if the system version does not meet the requirement.

Set up the Network Connection

Connect the Hardware

Plug the Ethernet cable of the IPC into the WAN port of the robot controller, as shown below.

robotware connection1

Set the IP Address

  1. In the Home interface of the teach pendant, select Settings  Network  Public Network.

  2. Select Use the following IP address, and enter the IP Address, Subnet Mask, and Default Getaway. The IP address of the robot should be in the same subnet as that of the IPC.

    robotware home
    robotware connection2
    robotware connection3
    The Ethernet cable must be connected to the WAN port. When setting the IP, be careful to distinguish between the robot IP address of the WAN port and that of the LAN port.

Load the Program Files to the Robot

Prepare the Files

Copy the program files into a USB flash drive. Please locate the folder where Mech-Mind Software Suite is installed and the files are stored in Mech-Center/Robot_Server/Robot_FullControl/abb/server on ABB.

Folder Description

config_robware7

Robot configuration file that defines the signals required by the master-control, the auto-loaded module, and task types

MM_robware7

The robot program module

Backup

Before operating the robot, please follow the backup instructions below to back up the system so that the robot system can be restored if an incorrect operation occurs.

  1. Select Settings  Backup & Recovery in the Home interface.

    robotware home
    robotware backup1

  2. In the Backup window, modify the Backup Name and Location and then tap Backup.

    robotware backup2

  3. Click OK in the pop-up window to complete the backup.

    robotware backup3

Reset

There are two types of resets, which are resetting the system and resetting RAPID.

  • Resetting the system will restore the default system parameters and RAPID program, and the I/O configuration will be reset too. If a communication board or other communication devices are used, they should be re-configured after the system is reset.

  • Resetting RAPID will delete the current RAPID program and data, while the system parameter settings will be retained.

Reset RAPID

Please determine whether you should reset RAPID according to the following flowchart.

reset

  1. Select Settings  Backup & Recovery in the Home interface.

    robotware home
    robotware backup1

  2. In the Reset user data window, select Reset RAPID, and then tap Reset.

    robotware reset1

  3. Click OK in the pop-up window.

    robotware reset2

Reset the System (use with caution)

  1. Select Settings  Backup & Recovery in the Home interface.

    robotware home
    robotware backup1

  2. In the Reset user data window, select Reset RAPID and System Parameters, and then tap Reset.

    robotware reset3

  3. Click OK in the pop-up window.

    robotware reset2

Load the Files to the Robot

  1. Open RobotStudio, since the Ethernet cable is connected to the WAN port of the controller, click Add Controller and then select the controller and click OK. After the controller is added successfully, the controller management port will be connected automatically.

    load program1

  2. Import the two configuration files in the config_robware7 folder as shown below.

    You can select multiple files by pressing the Ctrl key and the left mouse button.
    load program2

  3. Select Confirm in the pop-up windows.

    load program3

  4. Follow the steps as shown in the figure below to copy the entire MM_robware7 folder and paste it to the HOME directory of the robot system.

    load program4

  5. Follow the steps as shown in the figure below to enable the RapidSockets network service.

    load program5

  6. Modify the safe zone threshold (in mm) in the safe_area.mod program according to the actual on-site work space of the robot.

  7. Click Restart to complete loading the program files.

    load program6

Run the Program

Reset the Program Pointer

  1. In the Home interface, tap Operate.

    robotware run

  2. Tap Tasks on the left and the list of tasks will be expanded. Tap Advanced on the right and the advanced settings will appear.

    robotware run1

  3. In the list of tasks, select T_ROB1, and select Reset Program Pointer to Main.

    robotware run2

  4. Select Yes in the pop-up window.

    robotware run3

Run the Program

  1. Tap icon controlpanel to open the Control Panel, and select Control  Auto.

    robotware run4

  2. Select Confirm in the pop-up window.

    robotware run5

  3. Select Motors on  Play to run the program.

    robotware run6

  4. Tap Messages in the upper left corner to view the Operator Messages. If messages as shown below appear, the program has been successfully loaded on the robot side.

    robotware run7

Test Robot Connection

Please refer to Test Robot Connection.

Troubleshooting

If the program has been loaded but the robot cannot be connected successfully, please check whether the following requirements have been met.

  • IPC side:

    • The firewall is turned off.

    • The IPC can communicate with the robot IP address with the ping command in the command prompt.

    • There is no interference from any antivirus software.

    • Two network ports of the IPC belong to different subnets and there is no conflict.

    • If the IPC is connected via a router, there is no interference from other network cables.

  • Robot side:

    • The Ethernet cable is connected to the WAN port of the controller properly.

    • The robot IP address is set correctly. Please ensure that the set IP address is that of the WAN port instead of others.

    • You have run the program on the robot side.

We Value Your Privacy

We use cookies to provide you with the best possible experience on our website. By continuing to use the site, you acknowledge that you agree to the use of cookies. If you decline, a single cookie will be used to ensure you're not tracked or remembered when you visit this website.

  • Preference
  • I accept
  • I don't accept